OUR 76 SERIES LAND CRUISER BUILD
The 76 (70) Series Toyota Land Cruiser has to be the best 4WD we have owned and we will never look back. The decision was made to purchase a 76 (70) Series Toyota Land Cruiser when we realised we needed a far better payload, greater towing capacity, better performance, longer range and overall reliability. Our goal has been to build the ultimate touring and towing 4WD for Australian conditions. As we have progressed through our 76 Series Land Cruiser 4WD build we have made quite a few changes to the 76 Series from stock. This includes interior upgrades, engine performance upgrades, and loads of external modifications. The below posts provide detailed information on all of these upgrades as well as detailed reviews on particular products and brands. We have summarised the different areas or categories of our 76 Series Land Cruiser build in our navigation menu above to try and make it easier for you to find the right information you are after. For detailed information on our 76 (70) Series Toyota Land Cruiser 4WD build read our posts below.
Custom 4-Inch Stainless Steel Exhaust on Our 76 Series Land Cruiser
In this post we show you our custom 4-inch stainless steel exhaust that we had made to fit around our auxiliary fuel tank.
Fitting a Second Tyre Carrier to Our 76 Series Uneek 4×4 Rear Bar Reconfirms Why We Dislike It
Read this post before you consider purchasing a Uneek 4×4 rear bar for the 76 Series Land Cruiser. Our experience has been terrible with this rear bar.
Fitting the Long Range Automotive 85 Litre Auxiliary Fuel Tank to Our 76 Series Land Cruiser
Read our post to see how and why we fitted the Long Range Automotive 85 litre auxiliary fuel tank on our 76 Series Land Cruiser.
Our Simple Cheap Water Storage & Pump in Our 4WD Touring Setup
See our cheap and simple water storage and pump solution for our touring setup.
Our 76 Series Land Cruiser Rear Seat Conversion is a Game Changer
In this post we take you through our 76 Series Land Cruiser rear seat conversion, showing you how it has made a huge difference to our setup.
The Cheapest 70 Series Land Cruiser Centre Console Upgrade
You do not need to spend a stupid amount of money on a centre console upgrade for the 70 Series Toyota Land Cruiser.
Why We Fitted Our UHF Antenna on Our Roof Rack with a Folding Antenna Mount
We show you how we moved our UHF antenna to our roof rack and the improvements made to signal transmission.
The Strongest Lightweight Bull Bar for the 70 Series Land Cruiser by Offroad Creative
We have fitted what we believe to be the strongest lightweight bull bar for the 70 Series Toyota Land Cruiser made here in Australia by Offroad Creative.
Fitting the Svnty Offroad Rear Barn Door Table for the 76 Series Toyota Land Cruiser
We show you how easy it is to fit the new lightweight Australian made Svnty Offroad rear barn door table for the 76 Series Toyota Land Cruiser.
The Total Cost to Build our 76 (70) Series Toyota Land Cruiser – Stage One
In our 100th blog post we thought we would share the total costs of stage one of our 76 Series Toyota Land Cruiser build.
Uneek 4×4 Rear Bar Review for the 76 Series Toyota Land Cruiser
After having our Uneek 4×4 rear bar fitted to our 76 (70) Series Toyota Land Cruiser for almost two years, we thought we would share with you why we would not recommend this rear bar for the 76 Series Land Cruiser.
Rhino Rack Pioneer Platform for the 76 Series Toyota Land Cruiser
In this post we review the Rhino Rack Pioneer Platform on our 76 Series Toyota Land Cruiser.
Do You Know How Much Your 4WD Wheels (Rims & Tyres) Weigh?
Do you know how much your 4WD wheels (rims and tyres) weigh? This is an interesting question and is something that is not always considered during a 4WD build.
BFG (BF Goodrich) KM3 Mud Terrain Tyres on Our 76 Series Land Cruiser
In this post we look at our BFG (BF Goodrich) KM3 mud terrain tyres that we had fitted to our 76 (70) Series Toyota Land Cruiser more than 40,000kms ago.
Our 4WD Inverter Setup Redarc 1000W Pure Sine Wave Inverter
In this 4WD build post we look at our inverter setup, our Redarc 1000W Pure Sine Wave inverter.
JMACX Billet Leaf Spring High Clearance Mounts
The JMACX leaf spring high clearance mounts for the 70 Series Land Cruiser can improve clearance by up to 30mm. Check out our post to find out more.
What to Consider Before Purchasing and Towing a Camper Trailer or Caravan
Towing a camper trailer or caravan, everything we believe you need to know. In this blog post we take you through everything that you need to consider when thinking about purchasing and towing a camper trailer, caravan, or something else that weighs more than 750 kgs. There are a few key points that need to […]
Redarc Tow Pro Elite V3 Electronic Brake Controller from Speedy Towbars
In this post we take a look at our Redarc Tow Pro Elite V3 electronic brake controller that we had fitted by Speedy Towbars.
ARB Large Tube Deluxe Steel Bull Bar 70 Series Toyota Land Cruiser
We review the ARB Large Tube Deluxe steel bull bar on our 76 Series Toyota Land Cruiser after more than 18 months of use. We take a look at what we like, some of the issues we have had, and why we are removing this bull bar and going to another brand.
Speedy Towbars 76 Series Toyota Land Cruiser Towbar
We take a look at our Speedy Towbars towbar for the 76 Series Toyota Land Cruiser that we have had fitted now for more than 18 months.
Drifta Rear Drawers Review 76 Series Toyota Land Cruiser
We review our Drifta rear drawer setup in our 76 Series Toyota Land Cruiser after 18 months of use. We go through all the features we love and what we do not like.
70 Series Land Cruiser Front Seat Fire Extinguisher Bracket by Svnty Offroad
In this post we review the new Svnty Offroad fire extinguisher bracket for the front seats of the 70 Series Toyota Land Cruiser. Another great Australian made product.
Custom Dyno Tune & ECU Remap by Just Autos
In this post we discuss our custom dyno tune and ECU remap that we had done by Just Autos. We achieved a 50% gain in power and a 114% increase in low end torque.
ARB Twin Onboard Compressor in Our 4WD (Maximum Output)
In this post we take a look at our ARB Twin Onboard air compressor setup in our 4WD and what we think about it 18 months on.
ARB Digital Tyre Inflator Review
In this post we review the ARB Digital Tyre Inflator that we use in our onboard air compressor setup in our 4WD after 18 months of use.
Our 4WD Suspension Setup Fulcrum Formula 4×4
In this post we take you through our suspension setup in our 4WD. We decided to go with a Fulcrum Formula 4×4 Big Bore suspension setup.
Our 4WD Dual Battery 12V Electrical Setup
In this post we take you though our dual battery 12V electrical setup in our 4WD. This is a detailed post taking you through all the gear we are using in our 12V setup.
Redarc DCDC In-Vehicle Battery Charger
In this post we take a look at our Redarc DCDC in-vehicle battery charger the BCDC1240D. We discuss the features and the installation including configurations and wiring.
CTEK CTX Battery Sense Battery Management Tool
In this post we take a look at the CTEK CTX Battery Sense battery management tool. This is a great and cheap option for getting all the useful data on your dual battery setup.
TPMS External Sensor Setup in Our 4WD
In this post we show you our OBD2 Australia external TPMS setup in our 4WD. Overall a fairly cheap but great addition to any 4WD in our opinion.
Lightweight Foam Gas Bottle Mount by Svnty Offroad
In this post we review the EVA foam gas bottle mount (holder) by Svnty Offroad manufactured here in Brisbane, Australia. This has been made to fit the Rhino Rack Pioneer Platform and we think this is the best storage option for a gas bottle on your roof rack. Check out our post to see why.
Svnty Offroad Maxtrax Angled Mounting Bracket for Rhino Rack Pioneer Platform
In this post we take an in depth look at the Maxtrax angled mounting bracket for the Rhino Rack Pioneer Platform by Svnty6 Fab. This is one of the new products coming out of Svtny Offroad all manufactured here in Brisbane, Australia. Great bit of gear, check out what we think.
Mullet Mods Rear Cup Holder Review
In this post we review and show you the Mullet Mods rear cup holder made in Australia for any 70 Series Toyota Land Cruiser. A super simple and cost effective modification to eliminate those Toyota factory annoyances!
Drifta Canvas Rear Wheel Bag
In this post we have an in depth look at our Drifta canvas rear wheel bag. Show you all the features and what we love about it.
Land Cruiser Build DIY Rear Drawer Additional Storage
In this part of the Land Cruiser Build we show you our DIY modifications to our existing Drfita drawers. These modifications give us a far better storage solution for all of our gear as well as lighting options in the rear.
Land Cruiser Build Runva Winch Install
In this part of our 76 (70) Series Land Cruiser build we show you what is involved in installing a Runva 13XP Premium winch. We did this on our own during COVID restrictions, would be far easier with a bit of help from some mates.
Land Cruiser Build Bonnet Struts
In this part of our Land Cruiser build we show you which bonnet struts we chose to install. We also show you what is involved in fitting these to your 4WD. Fairly straight forward but be prepared to get the drill out!
Land Cruiser Build Oil Catch Can
In this part of our Land Cruiser build we install a Pro Vent oil catch can kit that we purchased from Western Filters. Read this post to find out how easy it is to install and why you should have one.
Land Cruiser Build Fuel Pre Filter
In this part of our Land Cruiser build we install a Direction-Plus fuel pre filter kit that we purchased from Western Filters. This should be every 4WD owners first modification. Read the post to find out why.
Land Cruiser Build Snorkel
In this part of the Land Cruiser Build we fit a TJM Airtec Sealed Snorkel to replace the factory unit. Very simple self install that requires no cutting and uses all factory mounting points. Can be fitted in under 45 minutes especially if you read this post.
Land Cruiser Build Rear Solar Screens
For a couple of reasons we really wanted to screen our rear windows in the Land Cruiser. Firstly, to keep the Aussie heat out. Secondly, for some added security hiding all our gear in the rear.
Land Cruiser Build Floor Mats and Seat Covers
In this part of the Land Cruiser build we show you the floor mats and seat covers we chose to use. 3D rubber mats and neoprene seat covers. This has been our choice in all our 4WDs.
Land Cruiser Build Oricom UHF Radio
In this part of our Land Cruiser build we take you through the installation of our Oricom UHF and antenna connected up to our second battery. This was the first UHF installation that we have done and it went really well.
Land Cruiser Build Centre Console
We take you through our cheap centre console upgrade for a bit more storage up front.
Drifta 270 Degree Rapid Wing Awning
A look at our Drifta 270 Degree Rapid Wing Awning. How to install the awning and few things you need to know about this process. We also show you how easy it is to set the awning up.
Land Cruiser Build ARB Compressor
On board compressor install and what was involved to get our ARB twin compressor mounted and working.
Land Cruiser Build Drifta Rear Drawers
Drifta rear drawer setup and step by step guide for the installation of them. As well as fitting my dual battery before wiring.
Land Cruiser Build Uneek 4×4 Rear Bar
Installation of our Uneek 4×4 rear bar and tyre carrier as well as a Speedy Towbars tow bar.
Land Cruiser Build Wheels & Tyres
Wheels and tyres. BF Goodrich KM3’s and Dynamic Steel rims. Tyres are 285 75 16’s (33 inch). Rims are negative 25 offset and 8 inches wide.
Land Cruiser Build Sound Deadening, Towbar & Electrical
Sound deadening install and the start of all the electrical wiring for dual battery and tow bar.